Many LED tubes are “plug and play”, meaning you can just install them like you would a fluorescent bulb. For this to be true, look for bulbs that are “ballast-compatible” meaning that they can use the ballast already installed in your fluorescent fixture to power the LEDs.
Can I replace a fluorescent tube with an LED tube?
You can easily retrofit a fluorescent tube using plug and play or hybrid LED tubes. They are known as ‘universal ballast compatible’, and remove the need for any complex wiring.
Do I need to remove the ballast to use an LED bulb?
LED technology does not require a ballast to regulate the amount of energy flowing to the lights. LED’s require less energy and can be sensitive to excess energy. … Additionally, removing the ballast will reduce energy usage and result in even great cost-savings as ballasts continue to draw more power than necessary.
Should I replace fluorescent with LED?
Answer: Great question – and the answer is yes, an LED tube light can be installed in a traditional fluorescent tube light fixture, without the ballast. … Bypassing the ballast in a tube light fixture has the advantage of being more energy efficient – you can expect to save another 5 – 10% of energy use per fixture.
How do you bypass a ballast to install LED tubes?
How to Bypass a Ballast
- Turn off the power. Flipping the light switch to the “off” position does not necessarily end the flow of electricity. …
- Locate your ballast. …
- Cut the hot and neutral wires. …
- Cut the socket lead wires. …
- Remove the ballast. …
- Connect the input wires to the output wires.
Can you replace 4 foot fluorescent bulb with LED?
There is a wide variety of methods for converting to LED tubes. The simplest is to completely replace old fluorescent fixtures with brand-new LED fixtures. However, LED fixtures to replace four-bulb (8-foot-long) fluorescent fixtures (common in farm buildings) can set you back $100 or more per unit.
Do I still need a starter with an LED tube?
Conventional fluorescent tubes need a starter. This starter provides ignition voltage. Naturally, this isn’t necessary for LEDs, so the ignition voltage is superfluous. If you want to replace a traditional fluorescent bulb with an LED, then you must install a dummy starter or bypass the standard starter manually.
Can you bypass ballast for LED lights?
Since LED lights work on low DC voltage, they need a driver. Most T8 LED tubes do not need a ballast. So, if you are going to install a T8 LED tube light, it will require a ballast bypass unless you choose a ballast compatible T8 LED tube.
Can I replace mercury vapor bulb with LED?
LED corn cob lights are one of the most efficient ways to replace metal halide, mercury vapor, and high-pressure sodium HID bulbs.
Can you replace a sodium bulb with LED?
While upgrading to LED provides a lot of benefits, high pressure sodium (HPS) lamps still provide some of the most efficient lighting available. … LEDs, however, are better able to control their light, which is why a lower-watt LED can replace a higher-watt high pressure sodium bulb.
Are LED lights cheaper to run than fluorescent?
Other Factors. Both types of lighting are energy-efficient when compared to traditional incandescent bulbs. LED technology costs more than CFL and fluorescent lighting, but the LED bulbs also last longer and use less energy than fluorescent bulbs. … LEDs do not contain mercury or harmful gases.
Are LED tubes better than fluorescent?
LED tube lighting is the better choice because it lasts about 40,000 hours longer in testing, is more energy efficient, will save you more money, and will leave less impact on the environment.
Which is more efficient fluorescent or LED?
As good as fluorescent light efficiency has become, LED is better (and continues to improve at a more rapid pace). As long as fluorescent lights last, LED lights last much longer. Further, fluorescent lamps require the use of a ballast to stabilize the internal current that produces light.
Is ballast bypass safe?
The most significant negative to a ballast-bypass linear LED is the risk of electric shock since the sockets carry line voltage. It’s a common practice to place a finger on the lamp pins while you are trying to install it, and this becomes a risky endeavor when using single-ended ballast-bypass lamps .